Bristle
A dish of ferrofluid under a softbox. Hold to raise the magnet beneath the table, and the black mirror rises into hills. Drag to move it. Let go, and they sink, a little later than they rose.
what the picture can say about itself
- field over the magnet
- -
- critical field
- 17.22 mT
- the field
- rising
- hills
- 0
- height
- 0.00 mm
- the swell
- 0.00 mm
- the picture
- full
- fluid time
- real time
- the hand
- yours
- fluid grid
- 256 × 256
Ferrofluid is an oil with grains of iron oxide in it, too small to settle. Put a magnet under a dish of it and at first the surface only swells toward it. Then the field passes a threshold, and the flat black surface gives way all at once. It rises into hills about a centimetre apart, packed in hexagons. Take the magnet away and they sink, but later than they rose. On the way down they hold on a little past the field that raised them.
Nothing here is a recording. The fluid is APG512a, and the dish is the one Gollwitzer, Matthies, Richter, Rehberg and Tobiska used to measure this surface with X-rays, in a paper of 2007: 170 mm across, filled 10 mm deep. From their measurements of the fluid, the hills should appear at 17.22 millitesla and stand 9.98 mm apart. The piece works both out from the same numbers and gets the same answers.
How tall the hills grow is not in the simple theory. I fitted two numbers so they match what the X-rays showed: about 1.5 mm when they first appear, about 5 mm at 20.1 millitesla. They come out at 1.7 and 5.2. The magnet takes the field to 20.1 at most, where the measurements stop. Near the threshold the surface is slow to decide, so the hills take a second or two to come up.
One number came out wrong, and I have kept it. The field at which the hills let go on the way down sits 0.07 millitesla below the one that raised them. They measured 0.17. Their own computer model got 0.06, and they put the difference down to the edge of the dish.
These are the hills of a field just past the threshold, as it was measured. The tall thorns in photographs of ferrofluid come from fields many times stronger, and nothing here could reach them honestly.
Some of it is chosen. The magnet is a stack of ferrite 28 cm wide under the table, wide enough that its field covers the whole floor of the dish. I use only the upward part of its field, so the hills stand straight. The light is a softbox behind the dish and a strip light to one side. The lens is a 100 mm macro at f/11, 20 degrees above the table. The fluid is black, so everything you see on it is a reflection.
Press and hold to raise the magnet. Drag to move it under the dish, and the hills it leaves behind sink while new ones rise ahead of it. Let go and it lowers again. When no one touches it, the magnet wanders and rises on its own.
On a phone the piece watches how fast it draws and lightens itself. First it computes the fluid on a coarser grid, then it uses fewer pixels, and last it lets the fluid run slow rather than wrong. The panel above says what it gave up.
One thing I cannot settle from here. In this model the hills mostly stay where they stand while the magnet slides. I have written to Reinhard Richter to ask whether a real layer does the same, or whether its hills travel with the field.
Before any hill, the liquid swells. It heaps toward the stronger field, highest over the magnet and lowest at the edge. At full strength the difference is about a millimetre and a half. Rosensweig's book on ferrofluids gives its height from the field alone. Until October 20 I had left it out, so a first press showed two seconds of nothing. Amir tried it on his phone and told me. Now the reflection slides as soon as you press, and the hills follow about a second and a half later. I let the swell trail the magnet by an eighth of a second. That lag is my choice, and I don't model the liquid sloshing as it settles.
APG512a · a 170 mm dish · a 130 mm floor · 9.98 mm between hills