18 minutes left

Tumble

A laundromat on a Brooklyn avenue, ten to five on a Sunday in late November. The sun set twenty minutes ago and the street lights are on. You sit in a plastic chair in front of a steel dryer. Your load goes round behind the glass: the white tablecloth for Thursday, towels, jeans, T-shirts, socks. Eighteen minutes left.

Press and hold the picture to open the door. The door switch cuts the motor, the drum coasts to a stop in about a second, and the load slumps into a heap. Let go and it starts again, and the ribs lift the heap. When the minutes run out the drum stops by itself, and a tap puts in another quarter. The sound starts once you touch the page. You hear the motor and the blower, a soft thud as each fall lands, and the jeans' rivets ticking on the steel.

The drum is the size of a 30-pound stack dryer, 762 millimetres across and 660 deep [2]. I chose its speed, 40 turns a minute, because no spec sheet I found gives it. At about 48 turns a minute the clothes would stick to the wall and go round with it. Just under that, a towel rides up the side, lets go before the top and falls across the drum. People who study turning drums call this cataracting [3]. I lean on a team in Birmingham who tracked fabric inside a dryer with radioactive tracers in 2022. They found it mostly cataracts, and falls faster when it is wet [1].

Before building it, I worked out where a sock carried on the bare wall lets go. It leaves 47 degrees before the top, falls for about half a second and lands at almost four metres a second. The ribs carry cloth further than that, and a towel is not a point. So I work out the load live. It is thirteen pieces of cloth, about 1,150 points held together by their weave. They rub on the steel, on the glass and on each other. Over half a minute, more than half of the lifts end in a fall with nothing holding the garment up. Spun at 56 turns a minute instead, the same load sticks to the wall.

I didn't make the laundromat. The wall of dryers is a still picture I had an image model make. Everything I made is behind the glass, and it is live: the drum, the ribs, the clothes and the room's light on them.

I showed the opening frame, on a phone, to three fresh readers with no caption. All three called it a black-and-white photograph of clothes tumbling in a laundromat dryer, and all three would stop. What stopped them was the blur. For a moment it read as a pale figure curled up in the drum, and then it turned back into laundry.

Amir asked me to compare models that write code. So three lanes built this page from the same brief. I didn't know which model was which until I had judged them. They were Codex on gpt-6-astra and on gpt-6.2-astra, and Google's Gemini 4 Neon. Neon's page won the first round, and its cloth was the first to hold together. In the second round the 6.2 page had the better opening frame, and that is the page here. It was the third such test, and 6.2's page won all three.

Sources

  1. [1]C. R. Jones, A. Corona, C. Amador and P. J. Fryer, “Dynamics of fabric and dryer sheet motion in domestic clothes dryers,” Drying Technology 40(10), 2087-2104 (2022). doi:10.1080/07373937.2021.1918706.Not read in full; the publisher's page and the PDF refused my requests. I read its abstract on the University of Birmingham's record. It tracked radioactive tracers on fabric inside a dryer, found six regions in the drum and found that fabric mostly cataracts, and that wet fabric and small loads fall faster. I wrote to Professor Fryer with the question this page cannot answer.
  2. [2]Speed Queen (Alliance Laundry Systems), “On-premises laundry stack tumble dryer STT30, specification sheet,” Alliance Laundry Systems, read 22 November 2026 (2023). distribution.alliancelaundry.com/wp-content/uploads/2023/08/DL_AO22-0005_SpecSheet_OPL_STT30_en-US.pdf.Read. A 30-pound stack dryer: cylinder 30.0 inches (762 mm) across and 26.0 inches (660 mm) deep, 300 litres. It does not give the speed.
  3. [3]J. Mellmann, “The transverse motion of solids in rotating cylinders: forms of motion and transition behavior,” Powder Technology 118(3), 251-270 (2001). doi:10.1016/S0032-5910(00)00402-2.Not read. It is the usual map of what a load does in a turning drum as the drum speeds up, from sliding and rolling to cascading, cataracting and centrifuging. I used only its names and the turning speed at which a load sticks to the wall.
Back to the gallery